What is area?
Area is the amount of two-dimensional space inside a shape, measured in square units. A square that is 1 foot on each side has an area of 1 square foot, and a room that is 12 feet by 10 feet covers 120 square feet. The standard SI unit is the square meter, while acres and square feet remain common in US land and real estate.
Worked example
Example: A room is 12 feet long and 10 feet wide. Choose Rectangle, enter 12 feet for the length and 10 feet for the width, and the calculator returns an area of 120 ft².
Measure an L-shaped floor
Draw a line from the inside corner to the opposite wall to make two rectangles. If one is 12 ft by 10 ft and the other is 5 ft by 4 ft, use Rectangle above for each. Add 120 ft² and 20 ft² to get 140 ft² to cover. Measure each rectangle up to the dividing line to avoid counting any floor area twice.
If the box lists coverage in square feet, open the Flooring Calculator. Select Start blank, choose Measured net area, and enter 140 ft². For example, the Daltile Fabrique specification sheet lists 12.22 ft² per carton for its nominal 12 × 12 in. floor tile. Enter 12.22 as coverage per carton and 10% as an illustrative allowance. The required area is 154 ft². Dividing by 12.22 and rounding up gives 13 cartons. Use the coverage from your own carton and an allowance that fits your layout.
For a single area you calculate above, choose Use this area in Flooring after checking the result. Flooring opens with that one measurement ready to edit. Enter any combined area yourself when the project includes several shapes. For a slab of uniform thickness, choose Use this area in Concrete to carry the same measurement into the concrete order calculator.
Area formulas for common shapes
Rectangle
A plot 220 ft long and 99 ft wide covers 220 × 99 = 21,780 square feet, or exactly half an acre. A square is a rectangle with equal sides, so its area is side².
Triangle
If you know the base and height, Area = ½ × base × height. When you only know the three sides, use Heron's formula:
An equilateral triangle with 77 ft sides has s = 115.5 and an area of about 2,567.33 square feet.
Trapezoid
A trapezoid averages its two parallel sides and multiplies by the perpendicular distance between them. With bases of 29.528 and 9 and a height of 9, the area is 19.264 × 9 = 173.376.
Circle
A circular pond with a 15 ft radius covers π × 225 ≈ 706.858 square feet.
Sector
A sector is a slice of a circle. A 60° slice of a 16-inch-radius pie is one sixth of the whole: π × 256 / 6 ≈ 134.041 square inches.
Ellipse
Here a and b are the semi-axes, half the longest and shortest diameters. An ellipse with semi-axes 18 and 20 ft has an area of about 1,130.97 square feet. A circle is the special case a = b = r.
Parallelogram
The height is the perpendicular distance between the two bases, not the length of the slanted side. A base of 20 and a height of 18 give 360 square units.
Common area units
| Unit | Square meters |
|---|---|
| Square inch | 0.00064516 |
| Square foot | 0.09290304 |
| Square yard | 0.83612736 |
| Square meter | 1 |
| Acre (43,560 ft²) | 4,046.8564224 |
| Hectare | 10,000 |
| Square kilometer | 1,000,000 |
| Square mile (640 acres) | 2,589,988.110336 |
Tips for irregular spaces
Split an irregular floor into shapes that do not overlap. Calculate each area in the same units, then add them. Subtract any space you will leave uncovered if it was included in your measurements.
Remember that converting area units uses the square of the length factor: 1 yard is 3 feet, so 1 square yard is 9 square feet, not 3.
Choosing the right measurements
Each formula expects specific dimensions. For triangles entered by sides, the three edges must satisfy the triangle inequality (each side shorter than the other two combined) or no triangle exists. For trapezoids and parallelograms, the height is always measured at right angles to the bases. For ellipses, enter the semi-axes, which are half of the full width and height. For sectors, choose degrees or radians to match how you measured the angle; a full circle is 360° or 2π radians.
Each length has its own unit list, so you can mix units such as feet and yards. When all lengths share a unit, the result is reported in that unit squared; with mixed units it is listed in each unit you used. The conversion table translates it into the other common units so you do not need to multiply by squared factors by hand.