Miter Angle Calculator

About this calculator

Find the cut line for each board in a flat corner or regular polygon. Compare angles measured from the board edge and from a square cross-cut.

Measure face width across the board, perpendicular to its long edge. This worksheet models a flat joint with zero bevel.

Example measurements are shown. Use your own or calculate the example.

Embed this calculator

Paste this code into a Custom HTML block on your site. The calculator fits the width of the block. Adjust the height in the code if you want more room for results.

Find this widget in the publisher directory

How to calculate a miter angle for equal boards

Start with the included corner angle, the angle between the two long outer edges extending from the corner. For equal face widths, the seam splits that angle in half. The rotation from a square cross-cut is half the turn between the board directions.

Cut line to either board edge = included corner ÷ 2.
Rotation from square = (180° − included corner) ÷ 2.

For a 120° corner, the cut line is 60° from each long board edge. It is 30° from a square cross-cut. Both numbers describe the same cut using different references. If you measured a 60° turn between directions, select Turn between directions to describe the same corner.

How to calculate a miter for unequal board widths

In the plan view, point O is where the outer edges meet. Each inner edge is parallel to its own outer edge at a distance equal to its face width. Point P is where the inner edges meet. The seam runs from O to P. The calculator solves those two offsets and reads the seam angle separately from the long edge of each board.

For an included corner θ, the signed projection along the outer edge of Board A is (width B + width A × cos θ) ÷ sin θ. The cut angle for Board A is the angle from its long edge to the seam, accounting for whether the projection is positive or negative. Swap A and B in the formula to find the other projection.

For a 120° corner with Board A 100 mm wide and Board B 150 mm wide, the cut lines are about 40.89° and 79.11° from their respective edges. The corresponding rotations from square are about 49.11° and 10.89°. The shared seam is about 152.75 mm long.

Miter angles for a regular polygon

For an equal-width regular frame with n sides, the turn at each joint is 360° ÷ n. Divide that turn by two to get the rotation from square at each end. The included corner is 180° minus the turn.

Regular frameIncluded cornerCut line to edgeFrom square
Triangle60°30°60°
Square90°45°45°
Hexagon120°60°30°
Octagon135°67.5°22.5°

Read the reference before using an angle

In this worksheet, zero rotation means a square cross-cut. A negative rotation is possible when the seam is more than 90° from a board's labeled long edge. The sign belongs to the diagram. Compare the drawing with the scale and orientation of your own tool.

This calculation describes flat board faces with zero bevel. Crown molding with a spring angle and joints with tilted faces require compound geometry. The Bosch UniversalAngle manual describes simple and compound miter measurement separately. For a different triangle with measured sides, use the Triangle Calculator.

Frequently asked questions

What is the miter angle for a 120-degree corner?
For equal boards, the cut line is 60° from each long edge. The rotation is 30° from a square cross-cut.
What angle do I need for an octagon frame?
A regular octagon has 135° included corners. Each cut line is 67.5° to the long edge, or 22.5° from square.
Can I use two different board widths?
Yes. Choose unequal widths and enter both actual face widths. The calculator shows a separate angle for each board and their shared seam.
What does a negative rotation from square mean?
The cut line makes an angle greater than 90° to the board edge in the labeled plan view. The sign follows that drawing.

Formulas and sample results on this page were checked against independent references. Page last reviewed or updated . How we verify calculators. Project led by Shaun Connell.