Quilt Binding Calculator

About this calculator

Find how many cross-grain strips to cut for a rectangular quilt. See the fabric length and round up to the increment your shop sells.

Calculator inputs

Example: A 60 × 72 in quilt with 40 in usable fabric, 2.5 in strips, 10 in handling allowance and a 1/8 yd purchase step.

Calculate the example or use your measurements.

Controls are loading. JavaScript is required for interactive calculation; manual methods and the example below stay readable.

Square-ended cross-grain binding plan

Measure the straight-edged rectangular quilt after quilting and trimming.

Use the measured edge length, not a standard bed-size label.

Measure cuttable width after removing selvages and unusable ends; they are not deducted again.

Width before folding. Finished visible binding width is not inferred.

Excludes ALL automatically modeled initial strip joins and the final closing join. A bundled pattern allowance cannot be decomposed automatically. Zero adds no corner/handling extra.

Separate initial reserve along the bolt, not additional binding length. Zero adds no squaring reserve.

Each source-unit selector reinterprets the adjacent digits. Changing one requires Calculate again. The separate result views convert committed exact values.

Your actual seller increment; no universal shop step is assumed. Changing its unit reinterprets its digits.

Input syntax, exact limits and construction

Unsigned decimals (including .5 and 2.), a/b or whole a/b. At most nine digits per component or integer/fractional decimal part; leading zeros count. Improper mixed parts carry. No signs, exponents, commas, units in a token, expressions or Unicode numeric glyphs. Raw tokens allow 64 characters including outer ASCII whitespace; canonical sources allow at most 29.

Each physical source is at most 1,000,000 mm. Measured dimensions, usable width, cut width and active seller step must be positive; reserves C and T may be zero but cannot be blank. Usable strip length must exceed cut width. The 500-digit operation guard is a resource bound, not a sewing recommendation; derived counts/depths are not capped.

Only square-ended perpendicular diagonal strip joins and one identical final closure are modeled. The 45-degree stitch crosses a cut-width square; each centerline contributes its original length minus half the cut width. C excludes all those modeled join losses. This is nominal planning, not a material-sufficiency guarantee, cutting template, bias or pre-angled construction.

Embed this calculator

Paste this code into a Custom HTML block on your site. The calculator fits the width of the block. Adjust the height in the code if you want more room for results.

Find this widget in the publisher directory

The modeled binding construction

This planner cuts strips across the usable fabric width, overlaps square ends at right angles and stitches each overlap diagonally. Some quilting instructions call this straight-grain binding; the cut direction here is specifically cross-grain, not lengthwise parallel to the selvage. One final identical diagonal closure is reserved, even for a one-strip loop. This is nominal geometry, not a guarantee that an actual binding method will fit.

Why a join loses one cut-strip width

Let b be the cut strip width. Two square-ended strips overlap in a b by b square. The diagonal stitch crosses each strip centerline halfway through that square. Along the unfolded run, their contributions are L1 minus b/2 and L2 minus b/2, so their total is L1 + L2 - b. The quarter-inch seam allowance trimmed beyond an existing stitch line is not another centerline subtraction.

An open chain of n strips has n - 1 joins and length nF - (n - 1)b, where F is usable strip length. The final identical closure reserves another b, leaving n(F - b). This does not model pre-angled ends, tucked closure, shifted stitching or personal overlap adjustments.

Additional working reserve is separate from every join

The quilt perimeter is P = 2(width + length). Your additional corner/handling length C excludes ALL automatically modeled initial and final join losses. The smallest whole count is ceiling((P + C)/(F - b)), with F greater than b. C = 0 adds no corner or handling extra. A pattern's bundled allowance for seams and corners cannot be automatically split into this model's parts; do not silently paste it as though every convention were identical.

T is a separate initial squaring reserve along the bolt. It increases fabric cut depth, n times b plus T; it is not more binding length. Usable width already excludes selvages and unusable ends. No shrinkage, pattern-matching loss, finished visible width or physical-fit promise is inferred.

Worked example: eight strips, two purchase steps

Take a 60 by 72 inch quilt, usable width 40 inches, cut width 2.5 inches, additional C = 10 inches after all modeled joins and T = 0. The 10 inches is an editable example, not a sewing recommendation. Perimeter is 264 inches and working requirement 274. Eight strips provide 302.5 inches as an open chain; final closure reserves 2.5, leaving 300 inches nominally closed and 26 inches beyond the stated working requirement.

Eight strips use 20 inches along the bolt. At a seller increment of 1/8 yard, round up to 22.5 inches, or 5/8 yard. At a half-yard increment, the same cut list calls for 36 inches, or 1 yard. Neither seller step is universal. Without an increment, the tool labels 20 inches as unrounded fabric length rather than an orderable purchase.

A threshold that distinguishes open and closed plans

Seven 40-inch strips of 2.5-inch cut width give 265 inches open but only 262.5 after the modeled final closure. A 264-inch target can therefore fit an open-chain target while requiring eight under this closed-loop convention. No rounding of displayed decimals decides that threshold; exact fractions do.

Source units, privacy and useful output

Each source has its own unit. Changing that selector reinterprets its adjacent digits and requires Calculate again. Separate result views convert the exact committed physical quantities without replacing the source. Whole counts and seller thresholds remain exact. Long totals stay aggregate text; diagrams show only a few representative strips and are not cutting templates.

There is no account, autosave or automatic URL update. Copy and print use the current exact plan. Public links require explicit consent and include all active numeric source values, units, seller policy and output views. An inactive seller draft stays only in page memory and is omitted from the link.

Method sources and limits

Sewing & Craft Alliance guideline 9.240, Binding a Quilt shows square-ended perpendicular overlap with diagonal stitching; its final tucked closure is a different method. Janome's machine-binding tutorial describes a traditional closing overlap equal to cut width and its author's slightly different personal preference. Utah State University Extension's binding instructions pre-cut angled ends and use a bundled allowance rule; that construction is not treated as proof of this square-ended loss formula.

Method reviewed November 8, 2026. No bias layout, curved edges, other closures, shrinkage prediction, directional matching, precut substitution, stock, price or backing/batting/border planning is included. Use your pattern and chosen finishing method to set appropriate additional reserves.

Frequently asked questions

Is the cut width the finished visible binding width?
No. Folding, batting thickness and attachment method affect visible width; the entered value is the flat cut-strip width.
Why does one strip still have a closing allowance?
A one-strip loop has no initial inter-strip joins, but its two ends still need the modeled final diagonal closure.
Can I enter a pattern's usual extra ten inches?
Only if you intentionally interpret it as additional corner/handling reserve excluding all joins already modeled here. A bundled allowance cannot be decomposed automatically.

Formulas and sample results on this page were checked against independent references. Page last reviewed or updated . How we verify calculators. Project led by Shaun Connell.