Board and Batten Spacing Calculator

About this calculator

Find evenly spaced battens for one unobstructed accent wall. Choose a count or target gap and get the left-edge, center, and right-edge marks for each batten.

Editable example: 120-inch wall, 2-inch battens, 18-inch target gap, flush ends.

Calculate the example, or choose “Use my measurements” to start blank.

Calculator controls are loading. If JavaScript is unavailable, they stay disabled. The example and formulas below remain readable.

Changing units converts the view while retaining each exact original entry until you edit its digits.

Flush puts a batten against each wall edge. Open leaves the same clear space before, between and after the battens.

Closest is not a maximum: the chosen gap may be larger or smaller than your target.

Inch fractions apply to absolute positions, not repeated rounded steps. Metric views show decimals and exact ratios.

Memory only; included when you copy or print, and omitted from public links.

Use decimals or fractions such as 2.5, 5/2 or 2 1/2, with units selected separately. Up to 15 significant digits; no exponents, signs or expressions. Maximum measurement: 1000 m equivalent. Measure actual face width, not the nominal lumber label.

Example preview: 7 battens, 17.6667 in gaps

Flush ends; the 18-inch target is approximate. These marks belong to the editable example.

Wall overview

12345670 in · left wall origin120 in

Colored rectangles are battens; empty spaces are clear gaps. Numbers identify the table rows. Diagram proportions are illustrative; use the marks below.

Placement marks

Every mark is an absolute distance from the same left wall edge. Decimal marks are rounded to four places. Never add rounded gaps to find the next mark.

Absolute marks from the left wall edge; decimal unit: in
BattenLeft edge (≈ in)Center (≈ in)Right edge (≈ in)
1012
219.666720.666721.6667
339.333340.333341.3333
4596061
578.666779.666780.6667
698.333399.3333100.3333
7118119120
Exact measurements and marks

Exact gap: 53/3 in; pitch: 59/3 in. A less-than marker denotes a positive value below the decimal display threshold.

  1. 0/1 in; 1/1 in; 2/1 in
  2. 59/3 in; 62/3 in; 65/3 in
  3. 118/3 in; 121/3 in; 124/3 in
  4. 59/1 in; 60/1 in; 61/1 in
  5. 236/3 in; 239/3 in; 242/3 in
  6. 295/3 in; 298/3 in; 301/3 in
  7. 118/1 in; 119/1 in; 120/1 in
Embed this calculator

Paste this code into a Custom HTML block on your site. The calculator fits the width of the block. Adjust the height in the code if you want more room for results.

Find this widget in the publisher directory

Measure the face width you will see

Measure the usable horizontal wall span and the visible face of the batten. A nominal lumber size is a product label, not a measurement to substitute automatically. The layout assumes every batten has the same face width and the wall has no openings or other interruptions. Choose inches, feet, millimeters, centimeters or meters separately from the numeric entry.

Clear gap and center-to-center pitch

The clear gap is empty space between neighboring battens. The pitch is one batten width plus that gap. For example, a 2-inch batten and a 17 2/3-inch gap give a 19 2/3-inch pitch. They describe different distances; use the labeled table rather than treating gap and pitch as interchangeable.

Choose what happens at the ends

With battens flush at both ends, the first left edge is zero and the last right edge is the wall width. Seven battens create six gaps, or six simple panels. With equal open end gaps, the same seven battens have eight equal gaps: one before, six between and one after. This tool treats that simple vertical panel task as the same layout, rather than a separate calculator.

Let W be wall width, b the actual batten face width and N the count. For flush ends, clear gap g = (W − N × b) ÷ (N − 1). For equal open ends, g = (W − N × b) ÷ (N + 1). Flush needs at least two battens; open permits one. A count fits only when N × b is no greater than W. A zero gap is valid arithmetic and is labeled as touching battens.

Closest gap can be above your target

The editable example is a 120-inch wall with 2-inch battens and a target gap of 18 inches. Flush ends select seven battens, leaving 106 ÷ 6 = 17 2/3 inches between them. Equal open ends select five battens, leaving 110 ÷ 6 = 18 1/3 inches. That open-end gap is slightly larger than the target. Six open-end battens would give 108 ÷ 7 inches, which is farther from 18.

This is a closest-gap choice, not a maximum-gap guarantee. Nearby whole counts are compared by exact absolute gap error; an exact tie chooses fewer battens. The solver considers the full physically possible range before applying the supported limit of 500. If its best count exceeds that limit, it asks you to change the target or choose a count instead of pretending that 500 is optimal. Adjacent supported counts are offered as explicit alternatives; selecting one requires Calculate again.

Mark from one origin, not rounded steps

For each batten, mark its left edge at i × (b + g) for flush ends, or g + i × (b + g) for open ends, with i starting at zero. Add half the batten width for the center and the full width for the right edge. Each position is calculated independently from the left wall edge. Do not add a rounded gap or rounded pitch repeatedly.

For a 137-inch wall, 2.5-inch battens and eight flush-end battens, the exact gap is 117/7 inches. The exact last left edge is 134.5 inches and the last right edge is 137 inches. Left edges rounded independently to the nearest one-sixteenth inch are 0, 19 3/16, 38 7/16, 57 5/8, 76 7/8, 96 1/16, 115 5/16 and 134 1/2 inches. These are approximate tape marks; they do not change the exact endpoint.

Decimal displays round halfway upward to four places. Positive distances below that threshold use a less-than marker rather than an exact zero, with exact ratios available in the result. Optional fraction columns are absolute inch positions rounded halfway upward to the nearest 1/16 inch. Their headings still say inches when the decimal display is in feet. Metric views omit the inch-fraction columns. The diagram is an overview; the complete table supplies the marks.

Changing units and correcting a layout

A unit switch converts the visible view while keeping the original numeric entry and its exact unit for calculation and sharing. A converted view is identified as approximate. Editing those displayed digits deliberately makes a new entry. This avoids accumulating rounded conversions during a unit round trip. Invalid measurement text stays available for correction and cannot be silently converted into a guessed value.

Count and target drafts are retained separately in memory. Only the active mode affects the result or public link. Any measurement, mode, edge, unit, mark preference or local label change clears the old marks and public actions. Correct the input and calculate again. Use my measurements clears the example; Restore example asks before discarding your edits.

Copy, print and optional numeric sharing

Calculation runs locally in your browser without an account or automatic saving. Copy and print include the complete current table and optional local wall label. Public sharing starts unchecked. If you explicitly allow it, a link contains only active numeric measurements, exact entry units, count or target, edge choice and display preferences. Anyone with the link can read and recompute them. Your local label and inactive draft are omitted. If the supported URL limit is exceeded, retain your local layout and copy or print instead.

Scope and related tools

The interval formulas and examples here are independently derived. The Inch Calculator layout tool is a comparable decorative task, not an endorsement or the source of copied code. Real Cedar’s board-and-batten profile guidance describes overlapping exterior siding, a different installation problem. This decorative tool does not calculate siding coverage, fastening, structural spacing, cuts, stock purchases, wall height, rails, waste or material price.

Use the square-footage calculator for a separate wall-area measurement. The board-foot calculator totals geometric lumber volume and entered prices; it does not turn these decorative positions into a cut list.

Frequently asked questions

Does the count include the end battens?
Yes. In flush-end mode the count includes the batten at each wall edge. Seven battens leave six clear spaces between them. Open-end mode leaves an additional equal gap at each wall edge.
Why is the selected gap larger than my target?
The target means the closest achievable equal gap for a whole batten count. A gap above the target can be closer than the next smaller gap. This is not a maximum-spacing rule.
Can I use this to order exterior siding?
No. This tool places equal-width decorative battens across one unobstructed span. Exterior board overlap, openings, stock lengths, fastening and installation requirements need a different plan.

Formulas and sample results on this page were checked against independent references. Page last reviewed or updated . How we verify calculators. Project led by Shaun Connell.