Engine Horsepower Calculator

About this calculator

The Engine Horsepower Calculator estimates an engine's horsepower from a quarter-mile run. Enter the vehicle weight and either the elapsed time (ET) or the speed at the finish line (trap speed). The result is an estimate of the power the car delivered, not a dyno reading.

Embed this calculator

Paste this code into a Custom HTML block on your site. The calculator fits the width of the block. Adjust the height in the code if you want more room for results.

Find this widget in the publisher directory

Estimating horsepower from a quarter-mile run

You do not need a dynamometer to get a rough idea of an engine's output. Drag racing results depend on how much power the car has relative to its weight, so two numbers you can measure at the strip, the time to cover a quarter mile (about 402.3 meters) and the speed at the finish, can be turned back into a power estimate. The two methods below are empirical formulas, so the answers are estimates, not measurements.

The elapsed time (ET) method

hp = weight ÷ (ET ÷ 5.825)3

Weight is in pounds and ET is in seconds. Because time is cubed, a small improvement in ET implies a large jump in power.

Worked example

A 3,500 lb car runs the quarter in 12.0 seconds. ET ÷ 5.825 = 2.0601, cubed it is 8.743, and 3,500 ÷ 8.743 = 400.3 hp. Run the same car in 11.0 seconds and the estimate rises to 3,500 ÷ 6.735 = 519.7 hp.

The trap-speed method

hp = weight × (speed ÷ 234)3

Weight is in pounds and speed in miles per hour at the end of the quarter mile. The same 3,500 lb car crossing the line at 110 mph gives 3,500 × (110 ÷ 234)3 = 3,500 × 0.10388 = 363.6 hp.

Why the two methods disagree

ET depends on launch, traction, gearing and shift quality. Trap speed depends mainly on power and aerodynamics, because the car is already well into its run when it crosses the line. For that reason many tuners trust the trap-speed number more for the engine itself and the ET number more for the whole package. If the two estimates are far apart, the car is probably losing time at the start.

Precautions

  • The results are estimates. Wind, altitude, temperature, tire grip and driver skill all shift the numbers.
  • Use the weight of the car as it ran, including driver and fuel.
  • The formulas estimate power delivered to the wheels plus drivetrain loss, so they are closest to the crank horsepower figures manufacturers publish.
  • Only attempt timed runs on a closed course designed for it.

What is horsepower?

One mechanical horsepower is the power needed to do 550 foot-pounds of work every second, about 745.7 watts. Gross horsepower is measured on a bare engine without accessories, while net horsepower includes the alternator, water pump, exhaust and other equipment, so net figures run lower. Horsepower and torque are linked: hp equals torque in lb-ft multiplied by rpm and divided by 5,252.

Horsepower and performance

Power alone does not determine acceleration; power per unit of weight does. A 3,500 lb car with 800 hp has about 0.229 hp per pound, while a 4,500 lb SUV with 300 hp has about 0.067. The power-to-weight figure in the results lets you compare vehicles of very different sizes on equal terms.

Getting better data from the strip

The estimates are only as good as the inputs. Weigh the car with the driver and typical fuel on a scale instead of using the brochure curb weight, since a 200 lb error moves the result by about 6% for a 3,500 lb car. Use the time slip from a timing system with a reasonable reaction-time offset removed, and note the weather: dense cool air at low altitude gives more power than hot air at high altitude, so a hot afternoon run can understate what the engine can do.

Reading both results together

If the ET estimate is notably lower than the trap-speed estimate, the car is probably losing time off the line through wheelspin or a slow launch. If trap speed gives the lower figure, the car may be geared too tall or have high aerodynamic drag. Tracking both after every modification shows whether a change improved real power or only the launch.

Quick table for a 3,500 lb car

ET (seconds)Estimated hp
14.0252
13.0315
12.0400
11.0520
10.0692

Frequently asked questions

How do I estimate horsepower from quarter-mile time?

Divide the vehicle weight in pounds by (ET in seconds divided by 5.825), cubed. A 3,500 lb car running 12.0 s is about 400 hp.

How do I estimate horsepower from trap speed?

Multiply the weight in pounds by (trap speed in mph divided by 234), cubed.

How accurate are these estimates?

They are rough. Expect results within about 5 to 10% of a dyno reading for a well-prepared car, and worse with poor traction.

Should I include the driver in the weight?

Yes, use the total weight of the car as it ran, including the driver and fuel.

Formulas and sample results on this page were checked against independent references. Page last reviewed or updated . How we verify calculators. Project led by Shaun Connell.