Pace Calculator

About this calculator

The Pace Calculator works out your pace, your finish time or the distance covered when you know the other two. Pace results are shown per mile, per kilometer and as speed in mph, km/h, meters per minute and meters per second, with predicted times for common race distances and a full table of kilometer and mile splits.

Extra modes handle multipoint splits (pace between checkpoints), converting between pace and speed units, and estimating a finish time from how far you have already gone.

Use hh:mm:ss for per-mile or per-kilometer pace, or a number for speed units.
Checkpoints (total distance and total time)
Embed this calculator

Paste this code into a Custom HTML block on your site. The calculator fits the width of the block. Adjust the height in the code if you want more room for results.

Find this widget in the publisher directory

What pace means

Pace is the time it takes to cover a fixed distance, usually written as minutes and seconds per mile or per kilometer. Runners and walkers prefer pace to speed because it maps directly onto a watch: if your pace is 9:00 per mile, every mile marker should arrive nine minutes after the last. Speed is the same information turned upside down, distance per unit of time, and is common on treadmills (mph or km/h) and in track and cycling contexts (meters per second).

The pace formula

Pace = Time ÷ Distance
Time = Pace × Distance
Distance = Time ÷ Pace

Because the three quantities are linked by one equation, knowing any two gives you the third. The only work is keeping units consistent. One mile is exactly 1,609.344 meters, one kilometer is 1,000 meters and one yard is 0.9144 meters, so every conversion here passes through meters and seconds.

Worked example

Suppose you ran 10 kilometers in 50 minutes and 25 seconds. That is 3,025 seconds over 10 km, or 302.5 seconds per kilometer, which is 5 minutes and 2.5 seconds per kilometer. A mile is 1.609344 km, so the per-mile pace is 302.5 × 1.609344 = 486.83 seconds, or 8 minutes and 6.83 seconds. As a speed that is 3,600 ÷ 486.83 = 7.39 mph, or 11.9 km/h. Holding that pace for a full marathon (42.195 km) would take 42.195 × 302.5 = 12,764 seconds, about 3 hours, 32 minutes and 44 seconds.

Using the different modes

  • Pace: enter the time and distance of a run to see your pace in six common units.
  • Time: enter a distance and a target pace to see how long the effort will take.
  • Distance: enter how long you will be out and the pace you expect to hold to see how far you will get.
  • Multipoint: list cumulative checkpoints (for example each mile marker and the clock time at it) to see the pace of every segment and your running average.
  • Converter: switch a value between pace per mile, pace per kilometer and the speed units.
  • Finish Time: enter the distance already covered, the time elapsed and the total distance to project your finish if you keep the same pace.

Typical race distances

RaceDistance
5K5 km (3.107 miles)
10K10 km (6.214 miles)
Half marathon21.0975 km (13.109 miles)
Marathon42.195 km (26.219 miles)

Elite world-record paces are startling: men's marathon records sit below 2:55 per kilometer and women's below 3:10 per kilometer, sustained for more than two hours. For most recreational runners a marathon between 3:30 and 5:00 is a solid result, which is roughly 5:00 to 7:07 per kilometer.

Training with pace and heart rate

Pace tells you how fast you are moving, while heart rate tells you how hard your body is working to do it. Coaches often pair the two. Easy runs are usually done at a conversational pace where heart rate stays in a low zone, tempo runs sit near the effort you could hold for about an hour, and intervals push briefly above that.

Estimating maximum heart rate and zones

A common estimate of maximum heart rate is 220 minus your age, though formulas such as 208 minus 0.7 times age often fit adults better. Training zones are then expressed as a percentage of that maximum, or of heart-rate reserve (maximum minus resting heart rate). A zone around 60 to 70 percent builds aerobic base, 70 to 80 percent improves aerobic capacity, and 80 to 90 percent raises lactate threshold. Measuring your true maximum on a hard uphill effort or in a lab gives better numbers than any formula.

Aerobic and anaerobic exercise

Aerobic exercise uses oxygen to burn fat and carbohydrate at a pace you can sustain for a long time. Anaerobic exercise, such as hard sprints, outruns your oxygen supply, relies on stored glycogen and produces lactate, so it can only be held for short periods. Most distance training is aerobic, with a smaller dose of anaerobic work to raise top-end speed.

Why splits matter

Splits break a race into equal pieces so you can check whether you are on target. Even splits, or a slightly faster second half (a negative split), are usually the most efficient way to race. Starting too fast is the most common pacing mistake, because the energy spent early is paid back with interest late in the race.

Frequently asked questions

How do I calculate my running pace?
Divide your total time by the distance. For example, 50:25 for 10 km is 3,025 seconds ÷ 10 = 302.5 seconds per kilometer, or 5:02.5 per km (about 8:07 per mile).
What pace do I need for a sub-4 hour marathon?
A 4:00:00 marathon requires an average of about 9:09 per mile or 5:41 per kilometer.
How do I convert pace per mile to pace per kilometer?
Divide the per-mile pace (in seconds) by 1.609344. An 8:00 mile (480 s) equals 298.3 s, or about 4:58 per kilometer.
How do I convert mph to minutes per mile?
Divide 60 by the speed in mph. A treadmill set to 6 mph equals 60 ÷ 6 = 10 minutes per mile.

Formulas and sample results on this page were checked against independent references. Page last reviewed or updated . How we verify calculators. Project led by Shaun Connell.