Resistor Calculator

About this calculator

The Resistor Calculator reads a resistor's color bands and gives its resistance, tolerance range and, for 6-band parts, its temperature coefficient. It also totals any number of resistors wired in series or in parallel, and works out the resistance of a round conductor from its length, diameter and conductivity.

Separate values with commas.
Separate values with commas.
S/m
Used when the material is set to custom.
Embed this calculator

Paste this code into a Custom HTML block on your site. The calculator fits the width of the block. Adjust the height in the code if you want more room for results.

Find this widget in the publisher directory

Reading resistor color codes

Through-hole resistors are too small to print a value on, so manufacturers paint colored bands around the body instead. Hold the resistor so the bands are bunched toward the left (the tolerance band, often gold or silver, usually sits alone on the right) and read from left to right.

  • 3 band: two significant digits and a multiplier. There is no tolerance band, so the tolerance is ±20%.
  • 4 band: two digits, a multiplier and a tolerance band. This is the most common style.
  • 5 band: three digits, a multiplier and a tolerance band, used on precision resistors.
  • 6 band: the same as 5 band plus a final band for the temperature coefficient, which tells you how much the resistance drifts per kelvin of temperature change.

Resistor color code table

ColorDigitMultiplierToleranceTemp. coefficient
Black0× 1250 ppm/K (U)
Brown1× 10±1% (F)100 ppm/K (S)
Red2× 100±2% (G)50 ppm/K (R)
Orange3× 1K±0.05% (W)15 ppm/K (P)
Yellow4× 10K±0.02% (P)25 ppm/K (Q)
Green5× 100K±0.5% (D)20 ppm/K (Z)
Blue6× 1M±0.25% (C)10 ppm/K (Z)
Violet7× 10M±0.1% (B)5 ppm/K (M)
Grey8× 100M±0.01% (L)1 ppm/K (K)
White9× 1G
Gold× 0.1±5% (J)
Silver× 0.01±10% (K)
None±20% (M)

Worked example

A 4-band resistor striped green, red, blue and gold reads 5 and 2 for the significant figures, blue for a multiplier of 1,000,000 and gold for ±5%. Its value is 52 × 1,000,000 = 52,000,000 Ω, or 52 MΩ. With 5% tolerance the real part can measure anywhere from 49.4 MΩ to 54.6 MΩ.

A 5-band resistor striped brown, black, black, brown and brown is 100 × 10 = 1,000 Ω, or 1 kΩ, with ±1% tolerance, so it will measure between 990 Ω and 1,010 Ω.

Resistors in series

When resistors are connected end to end, the same current flows through each one and their resistances simply add up. The total is always larger than the largest single resistor.

Rtotal = R1 + R2 + R3 + ... + Rn

Example: 10, 2, 38, 23, 38, 23 and 21 Ω in series total 155 Ω.

Resistors in parallel

When resistors share the same two nodes, the current splits between them and the combined resistance falls. The total is the reciprocal of the sum of the reciprocals, and it is always smaller than the smallest resistor in the group.

1 ÷ Rtotal = 1 ÷ R1 + 1 ÷ R2 + ... + 1 ÷ Rn

Example: two 100 Ω resistors in parallel give 50 Ω. The same seven values used in the series example give about 1.2 Ω in parallel, because the 2 Ω resistor dominates.

Resistance of a conductor

A wire's resistance depends on how long it is, how thick it is and what it is made of. Longer wire adds resistance in proportion to length, a larger cross-section lowers it, and better conductors such as silver and copper have higher conductivity σ.

R = L ÷ (A × σ), with A = π × (d ÷ 2)² for a round wire

Example: 100 feet (30.48 m) of copper wire 0.05 inch (1.27 mm) in diameter has an area of 1.2668 mm² and, at σ = 5.96 × 107 S/m, a resistance of about 0.4037 Ω. Typical conductivities at 20 °C are silver 6.30 × 107, copper 5.96 × 107, annealed copper 5.80 × 107, gold 4.52 × 107 and aluminium 3.78 × 107 S/m. Resistance rises with temperature, so a hot conductor measures higher than these figures suggest.

Standard resistor values

Resistors are made in preferred-number series so that the tolerance bands of neighboring values just overlap. The E12 series, common for ±10% parts, has 12 values per decade: 10, 12, 15, 18, 22, 27, 33, 39, 47, 56, 68 and 82, multiplied by any power of ten. The E24 series doubles the count for ±5% parts, and the E96 series is used for ±1% precision resistors. If a calculated value is not a standard one, choose the nearest standard value or combine two resistors in series or parallel to get closer.

Frequently asked questions

Which end of a resistor do I read first?
Start from the end where the bands are closest to the edge. Gold and silver are never used as the first band, so if one end has a gold or silver band, that is the tolerance end and you read from the other side.
What does a gold band mean on a resistor?
In the tolerance position gold means ±5%. In the multiplier position it means × 0.1, which is how values under 10 Ω are marked.
How do I calculate resistors in parallel?
Add the reciprocals of each resistance and take the reciprocal of that sum. For two resistors this simplifies to R1 × R2 ÷ (R1 + R2).
What is the temperature coefficient band?
On 6-band resistors the last band gives how much the resistance changes per degree of temperature, in parts per million per kelvin. Brown, for example, is 100 ppm/K.

Formulas and sample results on this page were checked against independent references. Page last reviewed or updated . How we verify calculators. Project led by Shaun Connell.